Pacific G1/4 Pressure Equalizer Stop Plug w/ O-Ring - Black
Pacific G1/4 Pressure Equalizer Stop Plug w/ O-Ring - Black

Pacific G1/4 Pressure Equalizer Stop Plug w/ O-Ring - Black

In stock
P/N
CL-W086-CU00BL-A
USD$7,99


Thermaltake Pacific G1/4 Pressure Equalizer Stop Plug w/ O-Ring - Black

The Pacific G1/4 Pressure Equalizer Stop Plug fitting is made for helping release excess air or pressure in your pump. Finished in chrome/black-plated copper, the G1/4 pressure equalizer plug is designed to install on the top of reservoir, and utilizes leak-free design with a preinstalled O-ring. Enjoy the ultimate in custom PC water cooling configurations with high quality components from Thermaltake.

Tt LCS Certified

Tt LCS Certified is a Thermaltake exclusive certification applied to only products that pass the design and hardcore enthusiasts standards that a true LCS chassis should be held to. The Tt LCS certification was created so that we at Thermaltake can designate to all power users which chassis have been tested to be best compatible with extreme liquid cooling configurations to ensure you get the best performance from the best features and fitment.

Leak-free Design

Committed to deliver the highest quality, the fitting includes one preinstalled O-ring and allows proper connection to G1/4” thread, securing properly to any cooling components. Available in chrome and black finishes.

Remarkable Expansion

Thermaltake offers a full line of Pacific Series components for enthusiasts to build up aesthetically-superior water cooling systems by incorporating externally-modular upgrades for their chassis.

*Note:
1. Please keep the plug away from liquid.
2. Please check the reservoir immediately if the water level is rising.
3. Please maintain the reservoir 80% full when the plug is installed.


Caution

Thermaltake recommends the following steps to be taken before using the Pacific series radiators and water blocks

  • It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while preventing the entire cooling system – copper, brass, nickel, aluminum, and steel – from corrosion.
  • Fill the reservoir with coolant and cycle the power on and off several times while the pump pushing the coolant into the loop.
  • DO NOT let the pump run dry, when there is no liquid entering the pump turn off your power immediately
  • Fill the reservoir to the top as it will prevent air from going into the pump
  • If necessary tilt the system slightly from side to side to bleed the air out of the loop.
  • Place some paper towels under fittings and joining points to test for leaks.
  • Run the loop with the fill port open for about 24 hours to completely bleed the air out of the loop
  • Before starting, flush out your system correctly to prevent any coolant or unwanted particles sticking to your tubes, radiators and other cooling components.
  • Coolant might fade over time.

Cautions

Thermaltake recommends the following steps to be taken before using the Pacific series radiators and water blocks

  • To ensure a clean loop, flush and rinse your radiators and water blocks with distilled water prior to use.
  • Do not use tap water or distilled water as your coolant, it may harm your loop and reduce performance.
  • It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while protecting the entire liquid loop from corrosion.
  • Before storing your water cooling components, please clean, rinse and dry. This will ensure a longer lifespan for your components.

Thermaltake recommends the following steps to be taken after completing your water loop setup

  • It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while preventing the entire cooling system – copper, brass, nickel, aluminum, and steel – from corrosion.
  • Fill the reservoir with coolant and cycle the power on and off several times while the pump pushing the coolant into the loop.
  • DO NOT let the pump run dry, when there is no liquid entering the pump turn off your power immediately
  • Fill the reservoir to the top as it will prevent air from going into the pump
  • If necessary tilt the system slightly from side to side to bleed the air out of the loop.
  • Place some paper towels under fittings and joining points to test for leaks.
  • Run the loop with the fill port open for about 24 hours to completely bleed the air out of the loop.
  • Before starting, flush out your system correctly to prevent any coolant or unwanted particles sticking to your tubes, radiators and other cooling components.
  • Coolant might fade over time.
More Information
P/N CL-W086-CU00BL-A
Dimensions ∮18 x 12.9 (H) (mm)
Weight 12 g
Material CU
Applicable G1/4”
Screw Thread G 1/4

User Manual

  • File Name
  • Description
  • Size
  • Version
  • Release Date
  • Manual
  • Multi-language
  • 3.6 MB
  • 2017-01-12