Pacific PR22-D5 Reservoir/Pump Combo
Thermaltake launches the Pacific PR Series tube reservoir and D5 pump for the ultimate in custom PC watercooling configurations. Featuring exceptional performance and unrivalled reliability, the PR22-D5 is manufactured from high quality POM and PMMA material to provide a crystal clear, high performance, durable solution. By giving users ideal mounting, fitting and flow, the PR22-D5 is the right choice for PC enthusiasts. Choose from: 200ml or 300ml to make your system a showcase for all to see with the Thermaltake Pacific PR Series.
Tt LCS Certified
Tt LCS Certified is a Thermaltake exclusive certification applied only to products that pass the design and hardcore enthusiasts standards that a true LCS chassis should hold to. The Tt LCS certification was created so that we at Thermaltake can indicate to all power users which chassis have been tested to be best compatible with extreme liquid cooling configurations, ensuring you get the best performance from the best features and fitment.
Driven Performance
Made in Taiwan, PR22-D5 top cap supports rubber washers for a proper seal,
including two predrilled G1/4” ports for fittings. Featuring 6mm thick of the pipe wall, Pacific PR Series can
sustain the maximum pressure up to 99 PSI (Pounds per square inch). Also, users can easily open out the top
cap, cleaning the reservoir thoroughly.
Ultimate Speed Controller and High-lift Pumping
The PR22-D5 is designed with a manual speed control knob to provide five speeds. Maximum discharge up to 1135L/hr provides high-performance cooling to your components. High-lift pumping of the pump head reaches up to 15 feet high at the maximum speed. Enthusiasts can build up advanced liquid cooling loop, two GPUs, three radiators, or even more DIY components at the same time. The pump is compatible with Thermaltake Pacific Series reservoirs and fittings, further increasing system performance, providing ultimate control for your water cooling system.
Heat-resistant Acrylic Tank
The Pacific PR Series tube reservoirs are all made of reliable, light weighted POM and PMMA construction, which is crystal clear and highly durable. High quality acrylic (PMMA) tube maximum working temperature: 131℉ (55℃).
*PR15
Easy and Flexible Application
Along with two brackets connected to both ends, Pacific PR Series is solid hold inside the chassis and allows enthusiasts to build up superior water cooling system from an aesthetic standpoint and incorporate externally-modular upgrades for their chassis. The Pacific PR Series can be installed either horizontally or vertically, making the chassis out of the ordinary!
Cautions
Thermaltake recommends the following steps before using the Pacific series radiators and water blocks:
- To ensure a clean loop, flush and rinse your radiators and water blocks with distilled water prior to use.
- Do not use tap water or distilled water as your coolant, it may harm your loop and reduce performance.
- It is strongly recommended to use market-proven pre-mix coolant, such as Thermaltake Coolant 1000, for optimal performance and corrosion protection.
- Before storing your water cooling components, clean, rinse, and dry them to ensure a longer lifespan.
After completing your water loop setup, Thermaltake recommends:
- Use pre-mix coolant, such as Thermaltake Coolant 1000, for corrosion protection and performance.
- Fill the reservoir with coolant and power the pump on and off multiple times to ensure the loop is properly filled.
- DO NOT let the pump run dry. Turn off the power immediately if there is no liquid entering the pump.
- Fill the reservoir to the top to prevent air from entering the pump.
- If necessary, tilt the system to help bleed air from the loop.
- Place paper towels under fittings to test for leaks.
- Run the loop with the fill port open for about 24 hours to bleed air out completely.
- Flush the system correctly before starting to prevent any particles from sticking to your tubes and components.
- Coolant color might fade over time.
| P/N | CL-W082-PL00BL-A |
|---|---|
| Dimensions | 94.1 (L) x 87.4 (W) x 309.7 (H) |
| Connector | 4 Pin |
| Pump Speed | P1: 1,800 RPM P2: 2,550 RPM P3: 3,300 RPM P4: 4,050 RPM P5: 4,800 RPM |
| Material | POM+ PMMA |
| Capacity | 300 ml |
| Maximum head | 15 feet (4.5m) |
| Maximum Flow Rate | 1135 L/h |
| Maximum pressure | 50 PSI |
| Input Voltage | 8 ~ 24 V |
| Parts | 1. Stopper *1 (G 1/4 ) 2. Bracket *2 3. Clip *2 |
| Screw Thread | G 1/4 |
User Manual
- File Name
- Description
- Size
- Version
- Release Date
-
Manual
- Multi-language
- 1.9 MB
- 2015-08-05
