TH120 ARGB Sync AIO Liquid Cooler (US Only) TH120 ARGB Sync AIO Liquid Cooler (US Only) TH120 ARGB Sync AIO Liquid Cooler (US Only) TH120 ARGB Sync AIO Liquid Cooler (US Only) TH120 ARGB Sync AIO Liquid Cooler (US Only) TH120 ARGB Sync AIO Liquid Cooler (US Only) TH120 ARGB Sync AIO Liquid Cooler (US Only)
TH120 ARGB Sync AIO Liquid Cooler (US Only)

TH120 ARGB Sync AIO Liquid Cooler (US Only)

In stock
P/N
CL-W285-PL12SW-B
USD$79,99
TH120 is an all-in-one 120mm liquid cooler that supports 5V RGB compatible motherboards.

TH120 ARGB Sync AIO Liquid Cooler

Thermaltake TH120 ARGB Sync is an all-in-one liquid cooler which includes a 120mm powerful high static pressure fans, and a high performance radiator along with a water block, 16.8M RGB color lumination with pre-set lighting modes via the smart fan controller, or synchronize with motherboard RGB software for stunning RGB colors.




 
 
 
 
 
 

Caution
Thermaltake recommends the following steps to be taken before using the Pacific series radiators and water blocks
1. To ensure a clean loop, flush and rinse your radiators and water blocks with distilled water prior to use.
2. Do not use tap water or distilled water as your coolant, it may harm your loop and reduce performance.
3. It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while protecting the entire liquid loop from corrosion.
4. Before storing your water cooling components, please clean, rinse and dry. This will ensure a longer lifespan for your components.

Thermaltake recommends the following steps to be taken after completing your water loop setup
1. It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while preventing the entire cooling system – copper, brass, nickel, aluminum, and steel – from corrosion.
2. Fill the reservoir with coolant and cycle the power on and off several times while the pump pushing the coolant into the loop.
3. DO NOT let the pump run dry, when there is no liquid entering the pump turn off your power immediately
4. Fill the reservoir to the top as it will prevent air from going into the pump
5. If necessary tilt the system slightly from side to side to bleed the air out of the loop.
6. Place some paper towels under fittings and joining points to test for leaks.
7. Run the loop with the fill port open for about 24 hours to completely bleed the air out of the loop
8. Before starting, flush out your system correctly to prevent any coolant or unwanted particles sticking to your tubes, radiators and other cooling components

Sync with Motherboard RGB Software

Designed to synchronize with ASUS Aura Sync, GIGABYTE RGB Fusion, MSI Mystic Light Sync, and ASRock Polychrome. It supports motherboards with a 5V addressable RGB header, allowing you to control the lights directly from the software mentioned above without installing any extra lighting software or controllers. For more details, please visit ASUS, GIGABYTE, MSI, and ASRock official websites.

Category Caution
Chassis, ARGB Fan, ARGB AIO
  • The motherboard signal connector only supports a 5V header.
  • Make sure your motherboard software is the latest version.
RGB Memory, VGA Waterblock, Distro Plate
  • This product can only be used with either the TT RGB PLUS software or the dedicated Motherboard software. By having more than two applications open may cause conflicts
  • The motherboard signal connector only supports a 5V header.
  • Make sure your motherboard software is the latest version.
More Information
P/N CL-W285-PL12SW-B
Pump Rated Voltage: 12 V / 5V
Rated Current : 0.38A & 0.25A
Motor Speed : 3300 R.P.M
Water Block Material: Copper
Fan Dimension: 120 x 120 x 25 mm
Speed: 1500 RPM
Noise Level: 28.2 dB-A
Rated Voltage: 12 V & 5 V
Max. Air Flow: 59.28 CFM
Max. Pressure: 1.31 mm-H2O
Connector: 2510–3 Pin , 5 V ARGB header–3 Pin
Tube Length: 400 mm
Material: Rubber
Radiator Dimension: 153x 120 x 27 mm
Compatibility Intel: LGA 1851/1700/1200/1156/1155/1151/1150
AMD: AM5/FM2/FM1/AM4/AM3+/AM3/AM2+/AM2

User Manual

  • File Name
  • Description
  • Size
  • Version
  • Release Date